Showing posts with label Aprilia Shiver. Show all posts
Showing posts with label Aprilia Shiver. Show all posts

Thursday, 13 August 2015

Comparo: Yamaha MT09 – Vs – Aprilia Shiver

Let me preface this with.........

I am not a professional motorcyclist, journalist or human-being. 

I am a daily commuter, weekend scratcher, sometimes tourer, ride with the hammer down,  and take my riding seriously.

I'm no track star. But have completed advanced training.

Over time motorcycling has deeply embedded into my life and identity.  
I love my Wife, my Dogs and Bikes – people can piss off. 

Let's begin.............

….....Soooo, I've been asked - “How does the Yam stack up compared to the Ape?”

Here goes. 

Motor/Throttle/Clutch
It's no secret the MT09 has a stonking triple banger. It was the power-plant offered by the Yamaha which made me seriously reconsider the MT09.

The 2015 bike has the updated ECU map straight out of the crate and delivers very predicable throttle application. Yes, there is still hesitation on small throttle openings from fully closed – however it is nowhere near as snatchy as the 2013 I tested a couple of years back.  

Snap the throttle open in first or second and the front will play ball. There is immediacy and torque everywhere and once you ecplipse 5-6K RPM, the Tri-Pot comes over all excited and gets going like a stabbed-rat with vengence. 

It'll pull without hesitation and keep on going. License preservation is an issue. 

Off the line the front is hard to keep on the deck. Luckily smiles are free, otherwise this bike would cost you more than just tickets from the constabulary. 


That said, the Aprilia is no slouch – it's just not intense. The 750 offers an engine character which can only be found in the guise of an Italian V-Twin - visceral, emotive. Strangely, unlike other V's - the Ape likes to be revved - and it needs to be.

Unfortunately it runs out of puff pretty quickly. You can't be as lazy with this motor, it demands to be ridden, in the correct gear, to realise its potential. I like that. Makes you work for the reward. 

Off the bottom, the Ape is lurchy and can surge and hunt the Tacho for stability. This can be remedied somewhat through the addition of a 15T counter-shaft sprocket and an A/F adjuster such as the FatDuc. It cannot be eliminated all together. 


Each bike offers 3 throttle modes which can be switched on the fly. After a while you'll just end up using the most aggressive mode on either bike. It's a nice feature, albeit somewhat unnecessary.

Both bikes have great clutch action and feel with low friction points and minimal travel. 

The Yammy uses a cabled clutch with a non-adjustable lever – the reach is a little far for me and the lever length is quite long. I'm a two finger clutch guy so the stock levers are likely to be swapped out. 

Conversely, the Ape uses a hydraulic clutch – a very nice one – with a light action. The stock levers are adjustable, however the lever thickness (vertical-aspect) is ridiculous – I soon swapped these for Pazzo's and never looked back. 

Results
Yamaha = 9/10 
Aprilia = 6/10

Handling/Brakes/Suspension
We'll get the easy one out of the way first – brakes. 

Both bikes are equipped with non-switchable ABS. Both implementations are good. 

As a commuter ABS is nice to have, especially on those cold, wet and traffic clogged mornings when cagers are particularly unpredictable and moronic. 

Not something to rely on. Not Ever. But nice to have. 

Out in the hills, the ABS does not dilute braking power or performance. 
No problem with the brakes on either bike. If you want or need to stop, you will – no doubt. 
These bikes can and do stop much harder than you'll be prepared for. 

The suspension and handling characteristics is where the Yamaha and Aprilia differ the most. 

Firstly, the Yamaha's suspension is comedy. It's like having pipe-cleaners up front and a pogo-stick in the rear. 

I've dialed it in as much as possible on the stock boingers and for the daily grind, popping wheelies and the urban environment, it's fine, OK, manageable, acceptable? 
Hmmm....up to maybe 8/10 pace and commitment. then it gets a bit wild. 

I've had to adjust the way I ride somewhat and recalibrate my expectations – that's not entirely a bad thing as it required me to learn how to get on with the bike. 

The MT09 will tip in on a knife-edge and can change direction via thought alone, it just demands more work and finesse to keep it compliant. 

Trail-braking is key to get weight over the front when pushing harder. Brake application and release must be deliberate in order to load and unload the suspension as progressively as possible – being severely under-damped this is quite a chore. 

When on pace it gets a little shabby – if you intend on taking this bike to the track you'll need suspension work. For sure. 

The chassis is compact and taught. the seat height is low – you are very much a part of the bike – this is a good thing.


On the contrary, the non-adjustable front end on the Aprilia is pretty damn good for what it is, the rear is planted and when coupled with a longer chassis the Ape is stable when pitched over. 

The Ape takes more effort to tip in and change direction due to its higher centre of gravity and footprint; however once pitched over, it is less squirrely and more predictable. She does push wide getting on the throttle when cornering, requiring you to tuck her in with more inner bar pressure. Trusting she'll stay put. She will. 


I feel I am quicker on the MT09 than I was on the Shiver – however the MT requires me to work harder and demands more technique. 

Getting the Yam to dance is more difficult than the Ape – not a bike for a Greenie/Squid. 

Once I get the suspension sorted – this rating will change (I suspect) dramatically. 

Results 
Yamaha = 6/10
Aprilia = 8/10

Seat/Comfort
I'm not a big guy. 
Not tall, not all that heavy. 
~174 cm @ 68-70kgs




I can easily flat foot either bike – more easily the MT09 as the Shiver has a wider saddle. 

The MT09 seat is on the firm side, however even after a couple of hours on the bike it does not cause me trouble. The Shiver might be slightly more comfortable, but I'd be splitting hairs to call a clear winner on comfort. 

Both bikes have wide bars with a natural reach – no shoulder or wrist pressure. 
All. Very. Comfortable. 

Foot position is slightly more rear-set on the Shiver, the MT09 is very Motard in the configuration of its controls. 

No clear stand-out for this component, both bikes offer a great naked-bike experience. 

Results
Yamaha = Aprilia = 8/10

Dash/Switchgear 
The Yamaha delivers a somewhat Spartan dash and instrument cluster. 
For the most part – it's not bad at all. 

It's a monochrome, black on white affair, with clear indications and read-out. Gear position, speed and RPM are all there and are updated promptly. It's easy to read and doesn't suffer sunlight washout or night dazzle. 

A fuel gauge is included, but you'll need to scroll for temperature – both intake (air) and coolant (engine) which is annoying. 

The real prize though is the ability to alter cylinder mixture using the on-board calibration. Yup, you can update the ECU closed loop setting straight off the bike – damn, that's good. 

The MT09 switchgear and blocks are clearly budget, albeit functional. They don't give the impression they are not up to the job or that they are about to fail, they're just not “considered.”




On the other hand, the Aprilia has a much more sophisticated dash – which is both good and bad. 

The good – constant air and engine temperature readouts, gear position, speed and large analogue Tacho.

The bad – speed and gear position indicators suffer latency between reality and readout. 
The cluster is temperamental, the slightest miss-use in terms of start-up or shut-down sequence will cause it to have conniptions. 
There is no fuel gauge – just a light.
It can fog.

In the Aprilia's defence, the switch-gear and blocks are superior and the tactile experience is more welcoming with better feedback. 




Results
Yamaha = 7/10
Aprilia = 6/10

Presence
Visually, the MT09 is much more minimal than the Shiver. More Skeletal. 
This bike is almost like an “Urban Scrambler” - lean, taught and ready for it. Get some. 
I'm running an Akrapovic raceline system (not shown in this picture), straight through, no catalyser, no baffle and yet she's more Hornet than Howitzer. 


In contrast, the Shiver is muscular, robust – a real looker. More bark than bite. 
She's statuesque, yet diminutive, simultaneously. A moving piece of Art.
The Akrapovic cat-back slip-on is a V-Twin symphony which is a Messerchmitt, not a Mouse. 





Results 
Yamaha 7/10
Aprilia 9/10

Belief/Trust
The mundane daily test must be applied. 
Which one would I trust? 
Which bike do I believe will start on a cold morning and not cost me the price of my first born to maintain?

'Nough said

Results
Yamaha = 9
Aprilia = 6

Totals 
Yamaha = 46
Aprilia = 43 

I must stress I have remained as objective as possible and am not surprised these bikes came out so closely. 

In many ways they are similar in their approach to being motorcycles; in other ways not so similar.

It just so happens the constraints where they are dissimilar they are also somewhat polarised. Opposite.

Thus when it's all said and done – both bikes offer a great package and riding experience. 

/BitSar

…............My brain hurts......so does my heart........

Friday, 5 June 2015

Yamaha MT-09. There are many like it, but this one is mine.

Today was both a day of sadness and happiness.
I was simultaneously and preemptively pining for the soon to be gone Ape, whilst excitedly anticipating the arrival of the new Yammy.

I busied myself in the morning with housework, bike-trade preparation and YouTube.
Trying NOT to play the waiting game......

Tick-tock.....

I'd been sitting in my riding gear for well over an hour - when the phone rings.
Yeah.........not toey at all..
The MT-09 is ready for pick up. Game on.

I make it to the dealer in record time to take delivery of the new girl and trade the old girl.
"Cheers fellas - see 'ya later."
Onto some black stuff.

First impressions of the MT-09A

The good:

  • The throttle mapping and ECU tune are greatly improved - dramatically so. Both A and STD modes are eager and satisfying whilst remaining usable. B-mode is not required. 
  • The mirrors are brilliant - excellent vision
  • The chassis is taught, tight and nimble with a small, flick-able footprint. 
  • That engine - sublime, tractable. Instant torque, instant response. A masterpiece.
  • The brakes have great feel and power, the ABS module has not diluted this. 
  • The gearbox is tight as a drum. I'm still breaking her in and clutchless shifts are laser precise. 
  • I LOVE THE ERGOS! Damn - nothing like a sit in bike steered by telepathy!

The not so good:
  • The OEM Dunlops are terrible - I'm going to reduce tyre pressure to shred them ASAP. Yuk!
  • The suspension is very soft. I have not yet adjusted from factory settings (plush), once I have dialled this in as much as possible I will reassess.

So. The time has come for this Blog to turn a corner.
Stay tuned for some Yammy antics.
Thanks Ape, you were a good girl. 

Day 1 - photo-roll.










/BitSar
I think I'm turning Japanese-A!........I really think so. 

Monday, 23 March 2015

Black dog ride - 2015

Sunday March 22nd marked the day for the Annual Black Dog ride - a ride I participate in each year, this year was no different.


The Black Dog ride provides awareness for depression and mental health and raises money to support integral services such as Lifeline. No more worthy a cause to pull on the boots, stuff my head into a helmet and throw a leg over the Ape......game on.

Like years in the past - I am riding as a corner maker to assist in the marshalling of the main bunch - this means the day starts early.

By the time I hit the road the sun is just up, the low-level fog is refusing to shift. The roads are damp. The tyres are cold. It's 9c and I have nearly an hour slab at free-way speed. Great!

The solution - base layers, thermal layers, wind-stopper layers and heated grips cranked. Slab done and done.

We meet at the official start point in Pakenham -  standard affair, corner marker briefing, then main bunch briefing, then go.



The corner markers head off, hitting the black stuff - most of the riders manage to follow most of the marshals, most of the time - most being the operative word.....

I'm dropped on a corner as we head into Yarra Glen - a marker-mate is dropped on the entry corner and I am on the exit. We're going to be here a while.

Ample time for me to remove my base layers and wind-stopper.

I get busy on the side of the road redressing myself.

I also take the opportunity to let some air out of the tyres - I'd been a little too generous with my set-up adding too much air when cold. The Ape was chattering around from both the front end and the rear - taking some air out, adds more give to the hoops, making her nice and compliant.

Done and done....




My marker-mate standing stoically - waiting for riders to marshal. The seriousness of it all is overwhelming. :))



And here comes a component of the main bunch - it did get quite spaced out this year......


We continue into Yarra Glen for a mid-ride regroup allowing any stragglers to catch up. A quick "splash and dash" for bikes with limited range and we're off again.

We point the bikes towards Toolangi then King Lake. Beautiful roads out this way - up the front, in the corner marker bunch we get a clear run through some pearler roads.

I'm dropped on another corner or two before the ride finishes up back in Pakenham - the local Lions club putting on a BBQ lunch with many hungry and deserving riders to feed.

All in all, another great run for a great cause.


See you all next year.
\BitSar
--getting redressed by the side of a road, marking his corner.

Sunday, 15 March 2015

Tail-light replacement

During the Touring Twins ride the guys informed me I was down one tail-light.

The Shiver uses a dual-filament lamp with each globe running a 12V and 21V rail.
12V for tail-light, 21V for brake.

Turns out one lamp was blown on both rails, no tail-light, no brake light.

So - time to replace them (both). Yeah, one is still good, but if I'm going in there to replace the blown lamp I might as well freshen them both up eh?



Step 1
Seat comes off and 8 fixings are removed:

2 x 12mm hex bolt
2 x 10mm hex bolt
2 x Phillips screw
2 x 3mm allen bolt





Step 2 
Move the grab-rail assembly and main fuses out of the way to allow access to the tail-light reflector and lens







Step 3
The lamp housing is locked into the reflector and lens via a removable ballast.

One quarter turn to the left and the globes are free.

It is somewhat fiddly getting the ballast out - however it can be done.









Step 4
Globes replaced and tested.
Done and done.



\BitSar

Sunday, 8 February 2015

Touring twins - the (not so) Shiver ride

There had been talk - for quite some time now - to get a bunch of Shivers together for an Italian-Ape blat.

Turns out one local Shiver rider is down with mechanical gremlins and a few others are MIA - no matter, the call went out and a total of 3 Shiver pilots popped up their heads.

A fellow Shiver rider (chillibutton) gathered a crew of 5, 3 x Shivers, 1 x BMW F800S, 1 x Firestorm. The common denominator? Twin cylinder engine configuration:

Italian 750 V-Twin = Braaaaarp
Japanese 996 V-Twin = Rrrrrrraaaarrrgh
Austrian (Rotax) 798 Parallel Twin = I need less fuel stops than all of you! (sorry, couldn't help myself petesul)

So - we were in business.......game on.

We met mid morning in the Eastern hills of Melbourne, quick "G'day" with the obligatory "Nice bike mate," then off - pointing the bikes towards Kinglake.

Traffic was acceptable - a few slow patches, but all in all a great fist leg - a mix of tighter twisties to open sweepers to flowing changes of left/right, left/right - very nice indeed.


The fun continued as we rolled into Beechworth Bakery in Healesville - a standard issue stop for riders.



Quick caffeine and food stop for the riders with a tank top-off for the bikes - sans BMW :)) - before heading towards Yarra Glen. 

Another wonderful route - the BMW pilot has fantastic local knowledge and directed the group through some pearler country side - zero traffic, excellent road condition and composition........absolutely magic!


The Ape - thoughtfully surveying the road travelled and the route ahead 


Along the way we pull over for a photo opportunity - bikes in their natural environment - in the hills, with plenty of black stuff travelled, with plenty more to go.

Ohhhh - I am a sucker for a Firestorm

Twin, twins......I wonder which one is the evil twin?


All in all - a fantastic run gentleman - cracker ride with an, even more, cracker group. Let's not wait so long before we head out again eh?

Oh.......I also managed to scrub away some of my commuter tyre shame........

'Till next time fellas.....

\BitSar 
-- hopefully sooner rather than later. 

Sunday, 21 December 2014

Toy Run - 2014

That time of year once more......Xmas....really? Already....bah!


Yet again, time for the annual MRA toy run. Get some toys, ride some road, give to kids....done.


An old mate whom I've not seen or ridden with for years was back in town after working interstate, then enlisting. He's keen for a toy run.




Added bonus? He's just bought an Ape. Another Shiver in the ranks.....game on.

We meet at my place and head off to one of the official start points in Port Melbourne. We're early this year so have time to get parked up reasonably well.



All types of bikes gather and gather. A larger turnout than last year, and - as always, VicPol were at the ready for an escort.


We'll take all sorts.....



Without breaking tradition we convoy out of Melbourne to Calder Park Raceway. Meh. It's hot, it''s a freeway - it's not for us......that's why we do it.







Once we arrive, donate some toys - have a wander around then point the bikes home.






The obligatory toy run pin.....to add to the collection.

\BitSar
Another year done.....

Sunday, 14 December 2014

15T - Shakedown

It was recently chain and sprocket replacement time - why not opt for a 15T countershaft sprocket eh? Adding a little more immediacy to acceleration and bringing that punchy torque curve a little lower sounded like a great idea to me.......game on.

Living in Australia severely limits choice in terms of aftermarket parts, especially for a Euro bike. The search began. 

I found one Aussie importer - however they could only source rear sprockets for the Ape. My dealer told me it was hard enough for them to get OEM sprockets, let alone third-party alternatives........bah!

After further looking - and reading about other Ape-ists sourcing parts via a UK seller I was in business. Order placed: 1 x AFAM 15T 525 pitch sprocket on the way


A shameless plug is now required - I am a pretty organised kind'a guy (some say, anal-retentive) - so I placed my order well in advance, giving the sprocket plenty of time to arrive.

Then a month went by.........
Then another 2 weeks........hmmm - time to contact the seller.

I purchased from UK seller biketorqueracing - once contacted, the response was immediate.
Adam from BTR provided parcel tracking details and followed up with me within 24 hours. Looked as though the sprocket was en-route and already within Australia.

Then another week went by........nothing

Got back in contact with Adam - he was willing to swallow the loss and send me another part at no cost. I am astounded. What service.

Turns out when I got home from the office that very day the initial order had finally arrived after being held up with border/custom inspection - good news for both me and Adam.

So! Now time to get this part on the Ape and get going.

As a commuter, the 15T provides a brilliantly smooth bottom end. 1st and 2nd gear slow creeping work is an absolute pleasure, no chugging, very little need to feather the clutch. The transition from closed throttle to small roll on when filtering in tight places is significantly better.

When you need to pick up and get your butt out of trouble the acceleration difference is noticeable - albeit manageable.

Commuter approved modification? Check.

But how about the fun stuff.......the weekend blat - when you've got a devil on your shoulder willing you to dance?

Yesterday called for a shakedown blat in the hills - and dance we did. The Ape: 'Au naturel'


On the fast open sweepers - being a little higher in the rev range and with the shorter gearing the throttle action/response has improved - very smooth with better feedback.

Powering out of tight twisties in 1st and 2nd gear will now let the front end skip across the top of the black stuff. Snapping open in 1st as the forks unload will loft the front hoop without too much trouble - much easier than stock........that little devil was having fun.......

The only criticism I would report, minor however still valid, would be long hi-way hauls.

I returned from the hills via the freeway and constant, steady-state ~100 - ~120+ kmh speeds is less comfortable - now hovering around 6k rpm......again - MINOR gripe......but it is worth noting.

Weekend scratcher approved modification? Check.

Obviously my speedo is now out - but meh, I rarely look/care what speed is being reported. I know when to be a saint or a devil.......

All in all, the 15T modification is one of, if not the ultimate, cost effective way to make the Ape more responsive, less chuggy off the bottom and hell of a hoot to ride - now even moreso....

Game on.

\BitSar
Devil on his shoulder willing him to dance.



Friday, 21 November 2014

Another "Not Forgotten"

I've been shit.......really shit in getting Blog pieces organised.

Getting married, moving, changing jobs etc.....Bah! No excuse eh!

There is an overnighter coming shortly.
Plus new Tyres (segue to long, long, long term Pilot Road 3 review)
Plus 15T
Plus further "formal" training.

In short......not forgotten - just getting more and more busy......life huh?

Back soon.
\BitSar

Saturday, 29 March 2014

Chocolate Run - 2014

Sooooooooo!

It's been ages since I've posted - this is not due to a lack of riding, this is due to a lack of anything resembling free time......bah!

But alas, it's Saturday morning and I have a small window of time to smash out some blog pieces - so here goes.

Sunday 9th of March 2014 was the annual Chocolate Run to the Mt. Franklin Chocolate Mill. This ride is traditionally a fundraiser ride for someone/something within the community.

In the past we've raised money to send an Athlete to the Para Commonwealth Games, donated to families who've had rider down, rider out situations and needed all the help they can get, to this year's run - raising money for the Black Dog Ride for mental health......... a worthy cause indeed and a great excuse to hit the hills with some old riding friends........woot woot.....

We had a good turn-out this year with approximately 40 riders - no larger than last year, in fact maybe slightly smaller......no matter - just ensures the tempo is kept a little higher and ample throttle is the name of the game.




We met off the freeway out west of Melbourne and pointed the bikes north.......get that first boring slab out of the way.



The first regroup at Woodend - take on some fuel, get some lunch, empty the bladder.....continue.....pretty standard issue.





Heading out of Woodend on the way into Daylesford, Hepburn Springs I am near the front of the bunch - Suddenly a frantic sequence of tail-lights flicker from the riders ahead......something's up.....they're all on the anchors......I immediately back off.

As I hit the crest I see the culprit - one very scared, very skittish, juvenile skippy (eastern grey Kangaroo for the international readers).......as EVERY Aussie rider knows, skippys are a dangerous prospect, not only are they a heavy and powerful animal, they also have ZERO road sense or spatial awareness, making them extremely unpredictable.....

This little fella crossed the road through the bunch no less than 3 times before finally somersaulting itself over a wire fence and back off into the bush. Poor little skippy - no Riders or Roos were harmed.

NB** This is not my footage or my bike - this footage belongs to a rider who participated in the Chocolate Run - original link here: youtube
                  This was the first pass the Roo made through the group, you can see it on the left as this rider avoids it. It was closer than it looks - trust me on that one.

Continuing out to the Chocolate Mill the ride played out as expected on our familiar route......we arrive, park the bikes and take a load off.....


A lovely KTM SuperDuke 1290R came along this year.........damn.....I need a towel

The Ape made an appearance

The bikes parked in the shade at the Chocolate Mill


Another good run this year - we raised enough money for the soon to follow Black Dog Ride - but who needs and excuse eh?

\BitSar
--easy now skippy

Saturday, 8 March 2014

Mini me......

Couldn't help myself.....

Came across this:




Nice little scale replica to sit on my desk.......

I've been quiet for a while - busy times.....alas - I have some posts almost ready to go...

New boots are being broken it, I have a fund raiser ride tomorrow and the subsequent charity ride in 2 weeks time.....

\Bitsar
**Slack (again) but for good reason.


Wednesday, 11 December 2013

Toy Run -2013

Every year me and my riding buddies participate in the annual MRA toy run for charity. This year was no different......

Giving toys to needy kids is the name of the game and the turn-out this year was very strong indeed, upward of 4,000 riders and pillions combined!

As always, everyone met at my place on Sunday morning before heading to the meet point - we were running late this year so had to start way at the back of the pack.......no matter, this ride is pretty sedate and boring - out of Melbourne, up the freeway to Calder park raceway - done and done.






We arrived middle bunch - many other feeder rides were heading in from all over the state.......a good turnout I should think - shame about the bloody weather! Bah! Melbourne eh?




(click to enlarge)



The Ape's in there - it's like a Where's Wally?


The amount of effort some riders put in to decorate both themselves and their bikes is quite astounding.....these guys took it pretty far - Reindeer and all!



Completely by chance I walked up to a Boulevard to grab a pick......got a tap on the shoulder....turned out to be the bike of an old Netrider mate who I haven't seen for ages - small world........


And of course, as is tradition, I got my 2013 commemorative pin to add to the collection - Happy Santa this year.

All in all - another successful run, another chance to donate some toys and give some needy kids some smiles........

\BitSar
--Ho, Ho, Ho!